Search:

Type: Posts; User: mondo

Search: Search took 0.00 seconds.

  1. Same result here, All 3 mode pins at5V.

    Same result here, All 3 mode pins at5V.
  2. Replies
    258
    Views
    294,691

    Sticky: Ray Massie, Australia Rapide Lite 200 LCD...

    Ray Massie, Australia

    Rapide Lite 200 LCD Upgrade, $US 88

    Would prefer refund now as I have RepRapDiscount LCD.
  3. Replies
    4
    Views
    4,524

    Thanks, did get it sorted in the end. Cheers

    Thanks, did get it sorted in the end.

    Cheers
  4. Aluminium as well No. 58

    Aluminium as well No. 58
  5. Replies
    66
    Views
    57,419

    I've managed to update the firmware such that I...

    I've managed to update the firmware such that I can now access the settings such as steps/mm etc for the extruder calibration.

    I made a video to run through the process for those not familiar...
  6. Replies
    9
    Views
    20,527

    Sticky: Zoom, Just what I've been looking for, Awesome....

    Zoom,
    Just what I've been looking for, Awesome. Thanks.
  7. Replies
    66
    Views
    57,419

    Found this web page and video that is a good...

    Found this web page and video that is a good guide and explanation. Its for a different machine but same marlin firmware....
  8. Replies
    66
    Views
    57,419

    Excellent. I had a quick look at the files. The...

    Excellent.
    I had a quick look at the files. The section that needs changing to access eeprom with M503 etc to check extrusion rate etc for calibration is in the "Configuration.h" file as far as I...
  9. Replies
    3
    Views
    4,273

    Looks like this is becoming common. I was having...

    Looks like this is becoming common. I was having intermittent thermistor problems, reading dropping to zero. traced it back to a break in the purple thermistor cable within the extruder wiring loom....
  10. Replies
    17
    Views
    13,617

    I've tried the same to no avail. From reading up...

    I've tried the same to no avail. From reading up on the marlin firmware there is setting that has to be enabled to allow interaction with the EEPROM. It would appear to my reading that Rapide have...
  11. Replies
    25
    Views
    20,242

    I had exactly the same experience. Tried to...

    I had exactly the same experience. Tried to identify the problem by looking at switch, poked and prodded, couldn't see anything in particular, so but the base plate back on and it's been working...
  12. Thread: ABS delamination

    by mondo
    Replies
    2
    Views
    6,520

    I had abs delamination problems till I turned the...

    I had abs delamination problems till I turned the fan off. I had to block the bottom duct as well since only one of the two fans turned off on my machine. I now use 235 deg on the extruder and 80 on...
  13. Replies
    4
    Views
    4,524

    I only have ABS at the moment, but have spools of...

    I only have ABS at the moment, but have spools of PLA on the way so will try once I have it and report.

    Cheers
  14. Replies
    58
    Views
    82,915

    I'm using ABS at the moment, supplied with...

    I'm using ABS at the moment, supplied with rapide. I don't have any other types at the moment but have a sample set on the way including wood, metal fill and various plastics including flexible. Got...
  15. Replies
    4
    Views
    4,524

    Cooling fan control and wiring.

    When I first started printing with abs I was geting alot of delamination. must add I'm new to 3d printing. eventually I worked out that the fan should be off. but found that setting the cooling off...
  16. Replies
    58
    Views
    82,915

    I've been getting the clicking as well. today...

    I've been getting the clicking as well. today tried a few things to investigate. lastvthing a tried was putting in a fresh nozzle. Bingo, back to smooth extrusion. did abit of googling on nozzles and...
Results 1 to 16 of 16