Search:

Type: Posts; User: sm0orb

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Sticky: Nice chart, will be useful for most.

    Nice chart, will be useful for most.
  2. Thread: Nozzle Flow

    by sm0orb
    Replies
    18
    Views
    14,884

    @Brodie: Maybe different versions of something on...

    @Brodie: Maybe different versions of something on the X-wing or the extruder that makes it work for some and not others (me). I fixed it by fileing a notch across the side of the axis at the right...
  3. Thread: Nozzle Flow

    by sm0orb
    Replies
    18
    Views
    14,884

    One more comment on Brodie's solution. I tried it...

    One more comment on Brodie's solution. I tried it and it did not work for me, when the grip wheel was aligned it extended a bit to much and so i cound not mount the head to the printer. Just a tad of...
  4. Replies
    18
    Views
    19,147

    Here is one. Most is open source but they want...

    Here is one.

    Most is open source but they want to keep some things closed.
    ...
  5. Replies
    14
    Views
    14,643

    First time i've seen one. :cool: Almost makes me...

    First time i've seen one. :cool: Almost makes me wish i had been patient and waited for one of those.:)
  6. @xyz Don't be too sad about that. It seems a bit...

    @xyz Don't be too sad about that. It seems a bit easier to disassemble the extruder with the plastic casing vs the alu.
  7. Replies
    130
    Views
    75,883

    Since you have had it working and it's now broken...

    Since you have had it working and it's now broken i wonder if you have done anything i between that may have caused the problem. For example install of new program.
    Worst possible cause may actually...
  8. Replies
    41
    Views
    27,611

    Saw a post on FB from Holgamods who had problems...

    Saw a post on FB from Holgamods who had problems getting long prints to work. He found a bad wire to his mainboard cooling fan. With that fan not working the board gets overheated and do strange...
  9. Replies
    22
    Views
    17,021

    That screw seems like a good way to fixate the...

    That screw seems like a good way to fixate the termistor, hope it works as planned.
    I had an idea about a thread(wire) runing up through the hole that rapide was planning to use for a fastening...
  10. Replies
    17
    Views
    13,107

    Sorry for delay. I just used a bit of hand force...

    Sorry for delay.
    I just used a bit of hand force to bend the frame outwards on the open end.
    This was with the supports mounted and made as i slid it on to the base, not bending so it changed shape...
  11. Well opening the base and check cables may be a...

    Well opening the base and check cables may be a good "break" from cleaning my hot end ;)
  12. Replies
    130
    Views
    75,883

    I have seen in some post here that there was one...

    I have seen in some post here that there was one user who got the printer recogized AS a printer. It even showed up in "devices and printers". That would mean there is a printer queue assigned to it...
  13. Replies
    22
    Views
    17,021

    Yes i was working on the heater block :( Thought...

    Yes i was working on the heater block :(
    Thought i had been really careful and also checked the cables but still missed it was out :(
    I have now disassembled the extruder again and found that at...
  14. Replies
    22
    Views
    17,021

    Smelly smoke leaked out

    Guess you all know what happened, termistor popped out of its hole. Luckily i was sitting next to the printer so only some smoke, no fire.

    But i think maybe the lining is burnt and will have to be...
  15. Replies
    17
    Views
    13,107

    HAve you tried just bending it out a bit ? Mine...

    HAve you tried just bending it out a bit ? Mine was also so tight they could not be set in place without bending out a bit in the bottom, don't remember if it was that mush though.
  16. Replies
    41
    Views
    28,401

    Second check on the wires would be a good idea i...

    Second check on the wires would be a good idea i think. If you have a possibility try using other cables alltogether for a test.
  17. Replies
    3
    Views
    3,925

    Think i will go for it. I'm thinking of...

    Think i will go for it. I'm thinking of elctronics printing wich requires two materials and don't mind the smaller size for that purpose.
  18. Replies
    41
    Views
    28,401

    One more idea. The hot end with nozzle and tube...

    One more idea.
    The hot end with nozzle and tube that is screwed in at the bottom of the extruder must be very tight. If not the nozzle will wiggle. That may lead to filament pieces placed on top of...
  19. Replies
    112
    Views
    50,238

    Second filament roll also that thin ? May be...

    Second filament roll also that thin ?

    May be time to tell Ethan, that filament isn't even close to decent quality. And it should have been prime.
  20. Replies
    41
    Views
    28,401

    Two questions. 1 Did you have any problem...

    Two questions.
    1 Did you have any problem threading one or both of the Z screws through the bearings of the X-wing ?
    If so you may have to turn it back and forth all across the screw in order to...
  21. Replies
    7
    Views
    6,097

    When cleaning the nozzle and block do check the...

    When cleaning the nozzle and block do check the threadings as well. I got melted filament in mine and it is really tedious to clear out. Heating, getting som out, heating again, over and over.
  22. Replies
    2
    Views
    3,790

    There are settings in several places in Repetier....

    There are settings in several places in Repetier. Some of the settings appear in more than one place and depending on how you use Repetier one or the other will be in effect. Settings in sliced...
  23. Looks like a neat tool

    Looks like a neat tool
  24. Replies
    66
    Views
    51,457

    "Paste" or "Compound" are probably just depending...

    "Paste" or "Compound" are probably just depending on the manufacturer language. The box i got is made by Fischer Elekronik in Germany and they call it "Wärmeleitpaste" wish they translate to "Thermal...
  25. Replies
    66
    Views
    51,457

    I checked a bit on CPU thermal compounds and got...

    I checked a bit on CPU thermal compounds and got a bit dissapointed. Most have a work temperature range only up to 100-120. Work temperature was not even listed in the comparison listings for the...
Results 1 to 25 of 108
Page 1 of 5 1 2 3 4