Search:

Sounds good TD, I will take your advice and measure a purge piece from both machines to find out the difference in size. Thanks for confirming the two size differences between the standard 0.35 and...

Thanks for removing the duplicate post TD. I didn't know I had done that. Thanks for trying to confirm the nozzle size SN, but I'm still unsure what you meant by, "I dint have Sure m8." What are...

Hello, I have a Cube Pro Duo in addition the a Cube3. I was wondering if the nozzle size (hole) on the Cube3 is the same as the nozzle size hole of the Cube Pro Duo? I think the nozzle hole size for...

Sounds risky, I would hate to push it to the point of damaging it. Good to know it's not impossible. I really like the current firmware, V1.14B, and would rather not change it, as sometimes other...

Does anyone know if you can print with nylon filament using the cube3. I have made the modifications with the cubetoolbox and I am able to print with other filaments, but I was wondering if I could...

Yes, that makes sense. Thanks for clarifying.

Ok, I'll take a look at that and get back to you.

- - - - - - - - - -

Ok, I'm confused, you said the system accounted for two layers, the first layer and the initial layer, but isn't the first...

Yes, the gap value at 0.35mm from touching the nozzle, is now zero to the system. I didn't know there were two layers the system was accounting for, the initial and the first layer. Where are you...

Just raise the print plate till it touches the nozzle, but does not push the nozzle. Just until light can no longer pass through the nozzle and the surface of the print plate. If the number measures...

It seems the solution I proposed was correct. After doing some troubleshooting, I finally figured it out. The trick was setting the layer height to .35mm when printing at 200 microns. I raised...

Thanks TD, this really helps!

Glad you liked the model. I have been struggling with this issue for a while and it has been the only thing holding me back. It would be great if I could solve...

Hello friends,

I've have printed on the cube 3 for a while now and I'm trying to understand the Z gap conundrum? I'm printing a part at 200 microns that has 24 holes and it has other parts that I...

I am using V1.14B TommyDee and it might be related to the temp error buddybu. Thanks for pointing that out guys. I will retry some abs on the left side again now that I have gotten the right side to...

Indeed TommyDee, it was heart dropping. Good to know what went wrong. Thanks for the explanation on the chip mismatch and nozzle. I'll keep an eye on it to make sure the chip is matched properly.

Hello friends, I ran into a problem after trying to use some abs filament using the cubetoolbox firmware hack. After installing the abs cartridge on the left side, I was prompted to load the correct...

Hello fellow cubers, I recently tried to run abs through my cube 3 and it has given me an extruder temperature problem detected and to refer to the user guide under section error codes:T12-221-L0-S1?...

Im trying to update the cube 3 printer firmware but I can't find where the cubetoolbox link is? I went to the thread but couldn't find the link to the cubetoolbox patch fix in step 1? Does anyone...

Not at all, just trying to wrap my head around it. Sounds like a breakthrough in resurrecting the EKOCYCLE/Lazarus from the dead. Jesus, eat your heart out! Love you guys for your persistence and...

Tomuro's solution? I'm not sure what that solves. Can you please elaborate?

- - - - - - - - - -

Thanks for chiming in buddybu, that's good to know before hand. I will configure Cube Print if...

Yes, I just ordered some gold, copper and silver and I can't wait to try it out, but i'm waiting to receive the order before I download and try the firmware patch. Now that I know how the printer...

Does anyone know if I need to assign filament colors from the swatch options in cubify slicer software after installing the new firmware patch? Do I just start using any filament color I want...

Ok, just saw your review on Bowden tubing TD. Very informative. Settled on the Capricorn XS, 2 meters, 2mmx4mm, low friction PTFE/bowden tubing for 1.75 mm filament. That really helped me narrow down...

TD, when you mention the two generic sizes, 1.75 and 3.00mm, do you mean that 3.00mm is the size of the tubing o.d. cause that's a big jump from 1.75mm to 3.00mm on the filament? Whats the standard...

Awesome! I can start looking for some online and try out the new firmware patch to bypass the proprietary filament cartridges. Thanks TD. Hope it works. I'll report back to the forum on the results.

Does anyone know the exact filament size I need to get for the cube 3 after I update the firmware with the cubetoolbox patch fix? Is it the same size as the original proprietary cartridges?