Search:

Type: Posts; User: StridAst

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    5,103

    Nozzle heating stopping at 150°

    Any suggestions for what to check to fix incomplete heating? My printer is only heating up to around 150 or so and it's just stopping there. I've tried changing both the heater and thermistor. No...
  2. I have decided I'm going to experiment with the...

    I have decided I'm going to experiment with the titan aero after all. If I have too much trouble fitting it to my RL200, I'll simply put it on my Wanhao i3. :D going to have to design my own adapter...
  3. the more I'm reading, the more I'm leaning back...

    the more I'm reading, the more I'm leaning back towards my initial idea of the titan aero. It might require designing my own mounting system, perhaps even casting such a mount in aluminum, but one...
  4. so when you installed your titan +e3d v6 on your...

    so when you installed your titan +e3d v6 on your printer, did you have to change the z endstop? It looks like the nozzle hangs much lower on those setups. trying to get a feel for what all I am...
  5. hmm fair enough, so if I go the aero route, I...

    hmm fair enough, so if I go the aero route, I would need to design some kind of custom bracket to lower it, which probably wouldn't help my print quality as that adds more flexibility in the mount...
  6. this is the extruder/hotend I am considering...

    this is the extruder/hotend I am considering...
  7. Replies
    19
    Views
    15,012

    lol thanks! Though I just barely got it to...

    lol thanks! Though I just barely got it to compile with arduino 1.0.5 r2. (had the same idea. thinking an older version of Arduino might work) good news is the LCD is functioning now :D I might...
  8. Replies
    19
    Views
    15,012

    I guess I will give that a try then. I was...

    I guess I will give that a try then. I was attempting to make this function like my Wanhao i3 does, since I'm quite used to that. ;) considering I have played around with the firmware, is there...
  9. Replies
    19
    Views
    15,012

    necropost. I figured since I'll be changing out...

    necropost. I figured since I'll be changing out things on my RL200 I would look into adding one of these. I bought the LCD screen a couple years ago before I mothballed my RL in disgust, where...
  10. I would gladly take a printed one if you don't...

    I would gladly take a printed one if you don't mind. let me know how much you would like for it, and the paypall (I assume) address :D
  11. ah ok so titan extruder and e3dv6 hotend. worth...

    ah ok so titan extruder and e3dv6 hotend. worth trying to swap out the board? or is that only "if needed" kind of thing?

    how did you attach it?
  12. Best suggestion to start over with a rapide lite 200?

    Ok, my rapide lite 200 has been collecting dust almost since it arrived. I had so many problems with getting it functioning (mostly filament feeding issues) that I simply gave up. I have been...
  13. Replies
    258
    Views
    236,019

    Sticky: Likewise I prefer to not post my real info on a...

    Likewise I prefer to not post my real info on a publicly searchable forum (if needed, pm me for it). But my dual extruder, nozzle me, and cradle me perks never arrived, and I lost all hope of ever...
  14. OK, posting my thoughts on this. The wanhao i3...

    OK, posting my thoughts on this. The wanhao i3 showed up, and I've got it up and running. First, the steel frame feels flimsy and wobbly compared to the rock solid feel of the Rapide lite. ...
  15. Replies
    19
    Views
    12,485

    I do plan on doing so. But not until I get a lot...

    I do plan on doing so. But not until I get a lot more practice in 3d design. I expect by the time I am ready to move up to a dlp printer, I will have more choices with possibilities anyways. :)....
  16. Replies
    19
    Views
    12,485

    hmm I might have to give carbon a try then, but...

    hmm I might have to give carbon a try then, but as for side by side on 50 microns vs 100, yes I have examined closely. I am a jeweler, and a lot of what I am printing has been small objects that have...
  17. Replies
    19
    Views
    12,485

    I figure that plastic is too flexible and this...

    I figure that plastic is too flexible and this might have more of an impact at high resolution prints. About 1/3 of the prints I have done so far are at 50 micron resolution so I use high resolution...
  18. Replies
    19
    Views
    12,485

    Considering printing something like this with...

    Considering printing something like this with moldlay filament, then casting it in bronze. Problem is I'll have to trim it down quite a bit to keep the weight down. :( wishing I had any experience...
  19. I actually preordered one of those from...

    I actually preordered one of those from makergeeks a month ago. I'll post in here when it shows up
  20. Replies
    8
    Views
    7,402

    I'll try replacing the nozzle next. I ordered...

    I'll try replacing the nozzle next. I ordered some on aliexpress a week ago, so I'll be waiting a bit for them still.

    Checking on the bottom fan next.
  21. Replies
    8
    Views
    7,402

    Yes I have printed the new extruder plate. The...

    Yes I have printed the new extruder plate. The toothed wheel is flush with the new extruder plate. I've double checked, the grub screw is definitely on the flat part of the shaft and is tight.
  22. Replies
    8
    Views
    7,402

    Extruder problems.

    So I keep having a recurring problem. On longer prints it will stop feeding. When this happens I can pull the filament out of the extruder without loosening the wheel any, cold. and the end of the...
  23. LCD screen from another printer on a RL 200?

    Just snagged a preorder on a wanhao duplicator i3.
    http://www.makergeeks.com/dui3de3dprfr.html

    Considering pulling the LCD screen and trying to work out how to put it on my Rapide lite. Think...
  24. Replies
    3
    Views
    5,729

    Thanks!! printing fine now :D hmm time to...

    Thanks!! printing fine now :D

    hmm time to google octoprint.
  25. Replies
    3
    Views
    5,729

    printer keeps randomly disconnecting.

    OK I've tried two different computers, I've tried repetier host and cura. My printer keeps randomly disconnecting. It freezes in mid print, and I am unable to do anything in repetier host to move...
Results 1 to 25 of 55
Page 1 of 3 1 2 3