Thanks Thanks:  1
Likes Likes:  1
Dislikes Dislikes:  0
Results 1 to 10 of 10
  1. #1
    3D Printer Noob
    Join Date
    Apr 2018
    Posts
    6
    Post Thanks / Like

    T14 T24 Temp Error codes

    I really need help. I have 4 good cartridges (PLA), and everytime I insert one, or both, regardless of switching sides, I always get an error code!!!

    Left side T14, right side T24.

    The printer never heats up all the way, and takes a long time before it actually shows the error codes T14 or T24.

    I dont know what to do. I already called 3D systems support and they basically had me run though a checklist, and no matter what I did, it always had those error codes...

    I know the main reason is that the print head is not in all the way, or not snapped into position. MINE IS! ALWAYS!

    HELPPPPPPPPPPPP!!!!!!!!
    Last edited by KHMusicMan; 04-23-2018 at 05:35 PM.

  2. #2
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,015
    Post Thanks / Like
    Try getting a new power supply...

  3. #3
    3D Printer Noob
    Join Date
    Apr 2018
    Posts
    6
    Post Thanks / Like
    Quote Originally Posted by bolsoncerrado View Post
    Try getting a new power supply...

    Thank you, good idea. Is there one maybe you would recommend?

  4. #4
    3D Printer God(dess)
    Join Date
    Nov 2016
    Posts
    1,329
    Post Thanks / Like
    T11-T21 Thermistor circuit - Possible short circuit detected (according to 3DS)
    T12-T22 Initial rate of change low - 3DS says to contact them
    T13-T23 High rate of temperature change detected - A sudden change in temperature was detected
    T14-T24 Low rate of temperature change detected - The rate of temperature increase is below the expected rate of change. [FIX]
    T15-T25 Set point deviation - The temperature is different from the target temperature

    ^ for posterity

    A low rate of change means something is not heating up fast enough.

    I am not sure that would constitute poor mating of the nozzle with the heater block.

    I was getting this error on one machine printing ABS every time within a layer or two of each print.
    Put the machine in a warmer place, and all was fine.
    This was a long time ago using stock cartridges before I even knew anything about this stuff.

    Just to be sure... you don't have a chip installed on the side that is not being used, right?
    That too will throw a Txx error.

  5. #5
    3D Printer Noob
    Join Date
    Apr 2018
    Posts
    6
    Post Thanks / Like
    Quote Originally Posted by bolsoncerrado View Post
    Try getting a new power supply...


    FIX!! SOLVED!!!

    IT WAS THE DAMN POWER SUPPLY!!!!

    There was a kink in the wire, so i decided to investigate. I cut open the wires, and one of the wires was broken open, I don't think there was enough contact. I twisted it back together... and IT IS FINALLY PRINTING!!

  6. Likes bolsoncerrado liked this post
  7. #6
    3D Printer God(dess)
    Join Date
    Nov 2016
    Posts
    1,329
    Post Thanks / Like
    What a find! Did it look like something that happened while in your possession or a factory blemish?

  8. #7
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,015
    Post Thanks / Like
    Quote Originally Posted by KHMusicMan View Post
    Thank you, good idea. Is there one maybe you would recommend?

    There's the exact model available for grabs on the internet. Can't remember the link right now. TD you got it handy?

    It's cheap enough to have one as a spare just in case.

  9. #8
    Regular 3D Printer
    Join Date
    Jul 2017
    Posts
    101
    Post Thanks / Like
    Straight from your post Bo!
    http://www.mpja.com/24-Volt-Adapter-...info/32885+PS/

    http://www.skycraftsurplus.com/mango...ptdc24v5a.aspx

    I'm in need of one too. Got a package deal a while back and it was missing the power supply.
    Last edited by ztoddman1; 04-24-2018 at 01:42 PM.

  10. Thanks bolsoncerrado thanked for this post
  11. #9
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,015
    Post Thanks / Like
    The first link is the same exact one 3DS supplies.

    The second link, Im not sure, just the specs, right?

  12. #10
    3D Printer God(dess)
    Join Date
    Nov 2016
    Posts
    1,329
    Post Thanks / Like
    That SkyCraft site is a great site! Thanks Todd.

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •