Printable 3D Objects / Parts for Rapide Lite

[Zoom]

Printable parts for the Rapide Lite 200 THINGIVERSE & Other Sites - LastUpdated 20 Jan 2015
Cable Tie Holder........by TiNkiN............................................ .....Cable-management-2.0_fixed_preview_featured.jpg
Washers for Bed and Extruder........by Claytonanderson..........Washers_for_Rapide_Lite_200_preview_featured.jpg
Tool Holder for RapidLite 200........by Synthius........................ToolHolder_preview_featured.jpg
Universal stand-alone filament spool holder..........................Universal_stand-alone_filament_spool_holder__Fully_3D-printable__Main_image_preview_featured.jpg
Cable Guide for Rapidlite 200........by Synthius.........................Rapidlite_Cable_Guide_preview_featured.jpg
.Filament Guide for Rapidlite 200........by Synthius....................Filament_Guide_preview_card.jpg
Extruder Plate for RapidLite 200........by Youmagine................ExtruderPlate.png
End Stop to Power off Printer…….........by TiNkiN….2.jpg...1.jpg
Plate Clip for RapideLite…..............by TiNkiN……..RL200_Plate_Clip_preview_featured.jpg...2015-01-12_13.24.29_preview_featured.jpg
Revised Extruder Plate...............by milstream…...................…...RapideLite200_extruder_plate.jpg
Rapide Lite Lamp Holder..................by jefish.............................Rapide-Light-Bracket.jpg
LED Light holder.................................................. ...LEDLights_preview_featured.jpgJanuary 29, 2015
Left and Right Tool Trays.......................................rl200_right_tray_preview_featured.jpgJanuary 29, 2015
Tray with Allen Wrench slots.................................allen_preview_featured.jpgJanuary 29, 2015
Filament Spool Holder by holgamods....................................rlspoolholder_v2_preview_featured.jpg
Anti-Noise Wedge by BobenhamHotspur................................Anti-NoiseWedge_preview_featured.jpg
Extruder Guide for Flexible Filament by claytonanderson..........rapide_lite_extruder_guide__3__preview_featured.jpg

X-Wing Cover v1 to v2 Update by RapideLite............................



Updated April 7, 2015

Calibration and Stress Tests"Your 3D printer is the best on the market? Prove it!"

Calibration Objects.Different materials and sometimes even different colours of the same type (and brand) of material may need slight different settings to get the best results…..Thingiverse hosts a large range of calibration parts. Depending on what you like to calibrate, there are parts for calibrating dimensions, stringing or other parameters that may be available.
Hollow calibration Pyramid................................Hollow_Pyramid_preview_featured.jpg........This hollow pyramid is used to test the retraction and temperature settings of your material.If the retract settings are not good enough, a lot of stringing will occur. Temperature and cooling settings are important to prevent the thin bars of the pyramid to melt down.If all settings are optimised, no stringing occurs, all bars have sharp corners, the touch perfectly at the top and the tip of the pyramid has a perfect point. Note however that it is almost impossible to get a perfect pyramid without any artefacts.
Surface Finish Calibration Test............................Surface_Calibration_Test_preview_featured.jpgThere are a lot of different things to look for in the surface finish.This part contains all kinds of different surfaces: straight vertical surfaces, a curved vertical surface a flat surface and a domed part.If this part prints OK, then you have most of the parameters set for a good surface finish on your parts.
Bridge Torture Test.................................................bridge-torture-test_50mm_preview_featured.jpgThe Bridge Torture Test is the ultimate test to verify bridging abilities of your printer.You need an optimal combination of temperature, cooling and the feed rate of your material.When the cooling of your printer is not enough, this bridge will not print correctly. It may collapse completely or a lot of loose filaments will be hanging from the bridge.To print this thing on a Leapfrog Creatr, make sure you have enough cooling on the extruder. I have not seen any of these printed on an unmodified Creatr.
Cooling System Test..............................................racing_vase_preview_featured.jpgThe nozzle cooler, which actually is a product cooler since you don't want to cool the nozzle but the material that was just printed, determines for a large part the surface quality of the objects you print.This model, called "Racing Vase", was made to test how fast your printer can race while still resulting in a good quality product. I have not tested this model yet but this seems a good test object for comparing cooler options.
Calibration Ring One Layer Thick.........................cal_ring_pic.jpgThis calibration file is awesome for seeing the high or low spots for where the extruder is laying the the filament. It is one layer thick so it works well. Designed to fit the rapide lite 200 3d printer perfectly but can be sized in print/slicer software like repetier.Cheers

[daf]

great job zoom

[bolsoncerrado]

Nice idea! Thanks!

[JonatanJacobsson]

Add this:
http://www.thingiverse.com/thing:612902

[synthius]

Thanks for sharing this Jonatan. I made several revisions to this before settling in on this one. I may move the wire tie holes closer to the base to make for a tighter fit but we'll see. I'm using it now and seems to work alright. Feel free to remix it.

IMG_20141229_072445.jpgIMG_20141229_072451.jpg

[Zoom]

Thanks for the Post it all helps Just Added it..........I wonder what will be next....

[BobenhamHotspur]

Nice work !!

[synthius]

I made a few improvements.
1. Increased the space between the screwdriver holes
2. Moved the wire tie hole closer to the base to make for a tighter fit to the motor mount.

I'm at work so i'm unable to print and test now but let me know if you try it. It takes about 2 1/2 hours to print with 0.25 layers and 15% infill.

[bolsoncerrado]

Add this one too

http://www.thingiverse.com/thing:508896

[Zoom]

Bolsoncerrado...thanks for the Post Added it to the list
I can see some of these part being used for mod's to the Rapide-Lite spool holder