Thanks Thanks:  1
Likes Likes:  2
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 12
  1. 01-20-2019, 04:16 PM #1
    tapsa
    tapsa is offline
    3D Printer Noob
    Join Date
    Jan 2019
    Posts
    2
    Post Thanks / Like

    cr 10 s4 bed heating time?

    Hi.
    I just bought cr10 s4 printer. It takes about 17 minutes to heat bed to 60 celsius degree. Is this normally? How about you?
    My room temperature is 20 celsius.

    I have checked wireling under the bed and also inside the PSU. Everything looks fine. Voltage is 220.
    Reply With Quote Reply With Quote
  2. 01-20-2019, 07:36 PM #2
    TommyDee
    TommyDee is offline
    Super Moderator
    Join Date
    Nov 2016
    Posts
    3,478
    Post Thanks / Like
    Welcome to the forum, Tapsa.
    I do not have a CR10 so I cannot confirm.
    Someone will weigh in soon.
    Reply With Quote Reply With Quote
  3. 01-20-2019, 09:41 PM #3
    bolsoncerrado
    bolsoncerrado is offline
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,332
    Post Thanks / Like
    Yes, S4 and S5 take ages to heat up... It's a very large surface and the bed heater covers MOST of it but not all of it...
    Reply With Quote Reply With Quote
  4. Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
    Likes TommyDee liked this post
  5. 01-22-2019, 08:19 AM #4
    Susanne
    Susanne is offline
    Regular 3D Printer
    Join Date
    Dec 2018
    Location
    Canada
    Posts
    49
    Post Thanks / Like
    I would say that, it is not normal. I have the CR-10 Mini and my bed takes less than 5-7 minutes to reach to 60C.
    Reply With Quote Reply With Quote
  6. 01-22-2019, 09:26 AM #5
    bolsoncerrado
    bolsoncerrado is offline
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,332
    Post Thanks / Like
    Perhaps your ambient temp is higher?
    Reply With Quote Reply With Quote
  7. 01-23-2019, 02:12 PM #6
    tapsa
    tapsa is offline
    3D Printer Noob
    Join Date
    Jan 2019
    Posts
    2
    Post Thanks / Like
    Hi. What you mean by that? Like I said room temperature is about 20C degrees.
    Reply With Quote Reply With Quote
  8. 01-23-2019, 05:14 PM #7
    bolsoncerrado
    bolsoncerrado is offline
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,332
    Post Thanks / Like
    That reply was to Suzanne not you.
    Reply With Quote Reply With Quote
  9. 02-01-2019, 03:49 PM #8
    Print Guy
    Print Guy is offline
    3D Printer Noob
    Join Date
    Feb 2019
    Posts
    13
    Post Thanks / Like
    FWIW - My CR-10s takes about 5 minutes to warm up to 75C.
    Reply With Quote Reply With Quote
  10. Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
    Likes TommyDee liked this post
  11. 02-01-2019, 07:03 PM #9
    TommyDee
    TommyDee is offline
    Super Moderator
    Join Date
    Nov 2016
    Posts
    3,478
    Post Thanks / Like
    Hey Print Guy. Welcome to the forum!
    Reply With Quote Reply With Quote
  12. Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
    Thanks Print Guy thanked for this post
  13. 02-08-2019, 07:23 AM #10
    Susanne
    Susanne is offline
    Regular 3D Printer
    Join Date
    Dec 2018
    Location
    Canada
    Posts
    49
    Post Thanks / Like
    Bolsoncerrado, my meaning is, my CR-10 Mini takes 5 to 7 minutes to go from room temperature to 60C.
    Reply With Quote Reply With Quote
 

 
« Previous Thread | Next Thread »

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules