Thanks Thanks:  5
Likes Likes:  0
Dislikes Dislikes:  0
Page 3 of 3 FirstFirst 123
Results 21 to 30 of 30
  1. #21
    Super Moderator
    Join Date
    Nov 2016
    Posts
    3,358
    Post Thanks / Like
    I have not tried to change a chip to wood because the software would have to recognize the chip and CubePro doesn't. Does the chip read back what you told it to write?

    edit; my bad - it does support wood... Let me see why this doesn't work.

    - - - - - - - - - -

    Use command 10,5,25;[enter] for wood.
    Last edited by TommyDee; 12-03-2020 at 08:30 PM.

  2. #22
    3D Printer Noob
    Join Date
    Nov 2020
    Posts
    4
    Post Thanks / Like
    I tried resetting the chip 100% then doing the change to wood and it worked! I don't know why that would make a difference but it now reads perfect on my pro

  3. #23
    Super Moderator
    Join Date
    Nov 2016
    Posts
    3,358
    Post Thanks / Like
    Some things can get confused. Confirm max amount and make sure it matches CubePro. I've made some bad updates to the chip but they always recovered.

  4. #24
    Regular 3D Printer
    Join Date
    Feb 2021
    Posts
    37
    Post Thanks / Like
    Hi All,

    Thanks for a great thread TommyDee, could not have done this without this thread.

    So after some head scratching I have figured out how to load the firmware onto the Nano . . . I think. I'll know tomorrow when I try to reload a chip.

    One note the batch file named the flash file as : ReCubelight.ino.hex , just change the file name to the same as the file in Tomuro's file which is : ReCube.ino.hex and it seem to work after that.

    Can anyone tell me what the : ReCube.ino.with_bootloader.hex file is for?

    Cheers

    RS

  5. Thanks TommyDee thanked for this post
  6. #25
    Super Moderator
    Join Date
    Nov 2016
    Posts
    3,358
    Post Thanks / Like
    I have not found use for the bootloader version.

  7. #26
    Regular 3D Printer
    Join Date
    Feb 2021
    Posts
    37
    Post Thanks / Like
    Hello All,

    Can some one please help, I have built my wand circuit and am able to reload my chip to 98% through Arduino IDE serial monitor with the command 8,99;<enter>.

    But I would now like to change the colour to black and the and the amount. Would the command 5,2;8,99;<enter> achieve that? Both are ABS. I understand that it is not possible to change material type with the lite version but is it possible to change the colour?

    Cheers,
    RS

  8. #27
    Super Moderator
    Join Date
    Nov 2016
    Posts
    3,358
    Post Thanks / Like
    Color is also a Pro feature.

  9. Thanks RicciEU thanked for this post
  10. #28
    Regular 3D Printer
    Join Date
    Feb 2021
    Posts
    37
    Post Thanks / Like
    Cheers TommyDee, Would it really matter if I used an ABS orange chip with ABS black filament?

  11. #29
    Super Moderator
    Join Date
    Nov 2016
    Posts
    3,358
    Post Thanks / Like
    None whatsoever. You can even slice it using neon green ABS in CubePrint 4.03

  12. #30
    Regular 3D Printer
    Join Date
    Feb 2021
    Posts
    37
    Post Thanks / Like
    Quote Originally Posted by TommyDee View Post
    None whatsoever. You can even slice it using neon green ABS in CubePrint 4.03
    Cheers TommyDee

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •