Thanks Thanks:  4
Likes Likes:  9
Dislikes Dislikes:  0
Page 5 of 27 FirstFirst ... 3456715 ... LastLast
Results 41 to 50 of 264
  1. #41
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,326
    Post Thanks / Like
    First "home" results on spanish users completing their Ciclops...









  2. #42
    Regular 3D Printer
    Join Date
    Dec 2014
    Posts
    157
    Post Thanks / Like
    Wow! Nice! What electronics did he usE?

  3. #43
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,326
    Post Thanks / Like
    I think they're using a CNC driver with a modified firmware... "or" some set up the shield using a breadboard...

  4. #44
    Regular 3D Printer
    Join Date
    Dec 2014
    Location
    Melbourne, Victoria, Australia
    Posts
    105
    Post Thanks / Like
    I was going to say did they already have the shield and board out already.... but obviously some savvy tech guru has found a way around it with a breadboard...... the main firmaware will work with the arduino uno since its the same chipset, you just have to figure out the pinouts etc..... much easier to buy the board and shield when they fully release it....

  5. #45
    Regular 3D Printer
    Join Date
    Dec 2014
    Location
    Melbourne, Victoria, Australia
    Posts
    105
    Post Thanks / Like
    Hi all! Been busy printing successfully and unsuccessfully LOL, managed to get all the parts printed out but had my batch of green PLA go bad half way through so had to switch to gray. I managed to find a nice cheap Logitech webcam from MSY computers here in Australia for AUD$25.00, so all I am waiting for now is the 2 lasers, the bearing and the board and shield.

    DSC_0051.JPG

    DSC_0052.JPG

    DSC_0053.jpg

    DSC_0054.JPG

    I hope the pictures came through ok....

  6. #46
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,326
    Post Thanks / Like
    Taking shape! Congratz!

  7. #47
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,326
    Post Thanks / Like
    Did anyone here print the "disc holder" yet? Can you send me the gcode you used?

    I'm still having issues with the layer displacement and so far I can discard DRV over heat (just happened on first layer, right after turning on the printer) and Y motor speed (tried with 6000, 5000 and 3000 mm/min with no luck).


    Thanks!

  8. #48
    Regular 3D Printer
    Join Date
    Dec 2014
    Location
    Melbourne, Victoria, Australia
    Posts
    105
    Post Thanks / Like
    Well I managed to upload the firmware to my Arduino Uno after much fiddling - the Horus software will use either UNO or the BT328scan board as a selectable option, and I have found a Chinese PCB maker to make 20 Zumscan PCB boards for US$80, I have ordered the parts from element 14 and now it is just a waiting game until everything arrives and I can put it all together and make sure it works before getting out to you guys. It should work out to about AUD$12-14 per board me thinks, I wont know the exact amount until I pay for the PCBS.....

    I should note that the A4988 driver isnt factored into the cost as you can buy them cheap on ebay... I am just doing the Zumscan board....

    Hey Bolson, I will see if I can find that gcode for you, I may have already deleted it, but I can reslice if necessary....
    Last edited by ned73; 02-24-2015 at 11:39 AM.

  9. #49
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,326
    Post Thanks / Like
    What slicing soft do u use?

  10. #50
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,326
    Post Thanks / Like
    Now that i realize, did you print the webcam support in 1 piece??

 

 

Similar Threads

  1. CowTech Ciclop: $99 3D Scanner DIY
    By jasonddsmith in forum 3D Scanning
    Replies: 4
    Last Post: 02-14-2016, 04:20 PM
  2. DIY Scanner, was it worth it?
    By Nigel in forum 3D Scanning
    Replies: 13
    Last Post: 10-19-2015, 09:59 AM
  3. LEWIHE Play - Made in Spain: Abrimos subforo en Español?
    By bolsoncerrado in forum LEWIHE Play Printer
    Replies: 0
    Last Post: 09-06-2015, 08:57 PM
  4. Replies: 45
    Last Post: 02-20-2015, 12:55 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •