Thanks Thanks:  0
Likes Likes:  1
Dislikes Dislikes:  0
Results 1 to 9 of 9
  1. #1
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,035
    Post Thanks / Like

    Smart print of the day!

    Lets try to keep this somehow alive!

    What about everyone suggesting at least an interesting "print of the day"? ONE post per day is the MINIMUM requirement in this thread!


    I'll start:

    http://www.thingiverse.com/thing:910216

    SHARKZ... Fun Multipurpose Clips / Holders / Pegs with moving jaws that bite!

    by muzz64, published Jul 4, 2015























  2. #2
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,035
    Post Thanks / Like
    http://www.thingiverse.com/thing:947423

    Finger Wrench (digit spanner)

    by francfalco, published Jul 29, 2015








    Description

    When you are in an awkward position trying to attach a nut to a bolt, a finger wrench may be just what you need. Tight corners especially, and anywhere that requires reaching into the unknown: dropping a spanner down the back of a radiator is all too easy, dropping your finger is not.
    I recently discovered this great little gadget on a DIY blog but unfortunately the company that originally supplied it is no longer making the product (why??) and i can't find anywhere to purchase existing stock.
    I had to have one, so I modelled and 3D printed this little beauty and it works a treat!
    Easy to use:
    There is a gap all down the back side, thereby allowing one size to fit a wide range of fingers. Slip a nut or bolt into the wrench as shown in the two images. Finger pressure keeps the nut or bolt in place. The tapered slot inside the wrench prevents the nut or bolt from turning.
    Suitable for 1/2inch nut/bolt and smaller.
    Print PLA or ABS 0.2mm 100% infill for strength.
    Enjoy!

  3. #3
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,035
    Post Thanks / Like
    Mankati Snail Shaped Filament Container
    http://www.thingiverse.com/thing:852621/


    by ChristinaL, published May 28, 2015




    There are three STL files including the upper part, the bottom part and the tubes. The tubes come in different sizes in order to match filament of different diameters. Note that you might want to set a denser infill to hold the filament properly.

    The whole set of the container takes around 60-80 hours to print. Originally designed by Mankati, and printed by a Mankati Fullscale XT Plus.


  4. Likes refriedchicken liked this post
  5. #4
    3D Printer Noob
    Join Date
    Jan 2015
    Posts
    4
    Post Thanks / Like

    Zip Top - Spinning Top

    Designed and printed this on my Rapide Lite in PLA at 15% infill and .15mm layer height. It'll print support free and can be downloaded here: https://goo.gl/5wbXEI

    Hope you like it!






  6. #5
    3D Printer Noob
    Join Date
    Jan 2015
    Posts
    4
    Post Thanks / Like

  7. #6
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,035
    Post Thanks / Like

    The Ultimate box maker

    The Ultimate box maker

    by Heartman, published Jan 13, 2016









    Open in Customizer



    Summary

    My first try with OpenScad,
    the box is fully customizable.
    I hope you will enjoy with it, and show us many boxes made with.
    If you play with the Round value you will go from the sharp to the round sides box
    If you want a chanfered box, set Resolution to 1.
    To export each single pieces, just set the other to "NO" value.
    The Top and Bottom Shells are the same,
    so it's not necessary to export them two times.
    Check the animation below to see how to setup your own box.
    You can change the text shape with any font listed here .
    Have fun
    Print Settings

    Printer Brand: RepRap
    Printer: Home made
    Rafts: Doesn't Matter
    Supports: Doesn't Matter

    Notes:
    Here is a small demonstration how to use the Customizer to have separate pieces box. The top and bottom shells are the same, so it's not necessary to make 2 differents stl files. If the front Panel is without text, then the back and front panels are the same, so again, just export one.

  8. #7
    3D Printer Noob
    Join Date
    Jul 2016
    Posts
    4
    Post Thanks / Like
    mechwarrior-catapult-bobcat-3d-model-print-01.jpgHow about this beauty? Not printed myself, found on web. If it were to choose a 3d printed figurine, this will be my favorite print ever!
    Attached Images Attached Images
    Last edited by Daby; 07-14-2016 at 01:52 PM.
    Collection of 3D printable models to be printed on desktop 3d printers. Wanna take a look?

  9. #8
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,035
    Post Thanks / Like
    Nice model!

    If you want to stealth spam, this is not the place though.

  10. #9
    3D Printer Noob
    Join Date
    Apr 2018
    Location
    Bilthoven, The Netherlands
    Posts
    14
    Post Thanks / Like
    Nice Models, I like this!

 

 

Similar Threads

  1. Replicape A smart and quiet 3D printer control board
    By bolsoncerrado in forum 3D Hardware
    Replies: 4
    Last Post: 10-28-2015, 07:55 PM
  2. Replicape A smart and quiet 3D printer control board
    By bolsoncerrado in forum Latest News
    Replies: 0
    Last Post: 10-25-2015, 09:53 AM
  3. Now THIS is a SMART and good example of flexible filament usage!
    By bolsoncerrado in forum 3D Print Materials & Filaments
    Replies: 0
    Last Post: 02-28-2015, 02:22 PM
  4. Customizing splash screen on the Full graphics smart controller?
    By Holgamods in forum Rapide Lite 3D Printers
    Replies: 2
    Last Post: 02-11-2015, 08:48 AM
  5. Replies: 0
    Last Post: 01-19-2015, 03:38 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •