Thanks Thanks:  11
Likes Likes:  7
Dislikes Dislikes:  0
Page 5 of 8 FirstFirst ... 34567 ... LastLast
Results 41 to 50 of 76
  1. #41
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,326
    Post Thanks / Like
    Aren't you trying nanodlp yourself sukhvir?

  2. #42
    Regular 3D Printer
    Join Date
    Jan 2016
    Posts
    93
    Post Thanks / Like
    I set it up a couple of weeks ago @bolsoncerrado, however had issues with it displaying layers. I'll give it another go soon, but am currently working on the dual vat build. Is anyone else going to attempt a dual vat system?

  3. Thanks bolsoncerrado thanked for this post
  4. #43
    Regular 3D Printer
    Join Date
    Nov 2015
    Posts
    88
    Post Thanks / Like
    Quote Originally Posted by sukhvir View Post
    I set it up a couple of weeks ago @bolsoncerrado, however had issues with it displaying layers. I'll give it another go soon, but am currently working on the dual vat build. Is anyone else going to attempt a dual vat system?
    Attempting a smaller single vat.. wish me luck

    Sent from my SM-G930V using Tapatalk

  5. Likes sukhvir liked this post
  6. #44
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,326
    Post Thanks / Like
    @sukhvir I had to move nanodlp SD card to a Raspi2 as I had HDMI issues with a Raspi3 with 6 HDMI cables I tested. All of them blanked out after a while. But the one I tested worked fine with the Raspi2 since minute 0.

    Either a deffective Raspi3 or an incompatibility with nanoDLP and Raspi3 code :???

  7. Thanks sukhvir thanked for this post
  8. #45
    Regular 3D Printer
    Join Date
    Nov 2015
    Posts
    88
    Post Thanks / Like
    @bolsoncerrado, So the screen just "blanks".. after a while?.. Can you elaborate a bit? .. After I get my new vat finished, the next step was Rpi3 and Nano... I also have a Rpi2.. May just go with that if there's problems with 3..

    @Sukvir, Do you have yours up and running with Nano?

  9. #46
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,326
    Post Thanks / Like
    yeah after a given amount of minutes, 2 or 3, you no longer get input from the pi hdmi no matter what. sometimes not even after fresh boot up.

    I'm printing now from pi2 eversince and hassle free. dunno if it was my pi or an issue with Nano but I guess if it was the later, someone else would have complained already.... or not. May be it's just this specific hardware (monitor).

  10. #47
    Regular 3D Printer
    Join Date
    Nov 2015
    Posts
    88
    Post Thanks / Like
    Are you liking running from Nano?

  11. #48
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,326
    Post Thanks / Like
    Definetly, nth times better than a laptop+CWS combo!!

    You dont burn a laptop display + computer cycles + having to loose a computer as it has to remain untouched as the print goes
    You can put the raspi inside the Morpheus and have a single solution all-in-one remote controllable (even adding a webcam in it)
    nanoDLP accepts STLs (CWS only opens OBJs)
    nanoDLP slices on the go (you can start printing already without waiting for the slicing to finish)
    nanoDLP allows pixel diming now
    and much more to come, I think

  12. #49
    Regular 3D Printer
    Join Date
    Jan 2016
    Posts
    93
    Post Thanks / Like
    Hi all and sorry @AngryPanda for late reply. We have our Kickstarter campaign kicking off next week so have been really busy getting things in place for that.

    My dual vat system is ready to run but the frame for it is a bit big and I haven't had time to take it to get it cut (it's a thick piece of acrylic). Hoping to get this done at some point next week and I'll keep you posted.

    In the meantime, here's a small teaser video and I'd appreciate if you could help to spread the word about the campaign. The computer has all been 3D printed by the way





  13. #50
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,326
    Post Thanks / Like
    Best of lucks with that, @sukhvir!

    You should program a Thunderclap for it too

  14. Likes sukhvir liked this post
 

 

Similar Threads

  1. Print Quality Troubleshooting Guide
    By bolsoncerrado in forum Latest News
    Replies: 1
    Last Post: 05-19-2018, 01:05 PM
  2. Post Processing and Finishing Thread
    By AngryPanda in forum Morpheus 3D Printers
    Replies: 15
    Last Post: 03-07-2016, 10:03 PM
  3. The Rapide Lite 3D Printers - Index / Summary Thread
    By bolsoncerrado in forum Rapide Lite 3D Printers
    Replies: 0
    Last Post: 06-03-2015, 01:29 PM
  4. Print Troubleshooting Pictorial Guide
    By bolsoncerrado in forum Latest News
    Replies: 0
    Last Post: 01-25-2015, 09:16 PM
  5. Repetier/Slic3r User Questions
    By Justin Keller in forum 3D Software
    Replies: 6
    Last Post: 01-08-2015, 08:10 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •