Thanks Thanks:  22
Likes Likes:  30
Dislikes Dislikes:  0
Page 7 of 9 FirstFirst ... 56789 LastLast
Results 61 to 70 of 89
  1. #61
    3D Printer Noob
    Join Date
    Aug 2016
    Location
    India
    Posts
    29
    Post Thanks / Like
    This is my first trial using Morpheus Resin (Base 30000ms and 10000ms) layer 0.2mm

    printed without any supports( any other software to generate support)
    Some layers or not sticking any suggestions

    1.jpg

    - - - Updated - - -

    Hi Sukhvir Please share, it will be very useful
    Quote Originally Posted by sukhvir View Post
    Hi folks. All seems quiet on the Morpheus forum front. Anyone printed anything they would like to share?

    Also, I've learned a bit more about how to successfully print larger items / print in pieces and join / finishing techniques. Not sure if anyone is interested.

  2. Likes sukhvir liked this post
  3. #62
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,037
    Post Thanks / Like
    Didnt even know we could buy Morpheus resin already???

  4. Likes karthik.pdy liked this post
  5. #63
    3D Printer Noob
    Join Date
    Dec 2016
    Posts
    1
    Post Thanks / Like
    Quote Originally Posted by karthik.pdy View Post
    This is my first trial using Morpheus Resin (Base 30000ms and 10000ms) layer 0.2mm

    printed without any supports( any other software to generate support)
    Some layers or not sticking any suggestions

    Hi Karthik, I have attached a photo giving my take on the issues you are facing. I have a bit of experience with SLA printing although I have been primarily an FFF/FDM operator up until recently. I hope this helps. Here is a link to Sukhvir talking about it a buildplate adhesion solution: http://www.print3dforum.com/showthre...ll=1#post32837
    Attached Images Attached Images
    Last edited by mojor; 12-27-2016 at 02:07 AM.

  6. Thanks karthik.pdy thanked for this post
    Likes karthik.pdy liked this post
  7. #64
    3D Printer Noob
    Join Date
    Aug 2016
    Location
    India
    Posts
    29
    Post Thanks / Like
    Hi Mojor thank for your feedback,@ Sukhvir need your support on this issue

    here is the ROOK successfully came with Morpheus Resin 0.07mm layers (Base 30000ms and 10000ms)

    IMG_0305.JPG

    Then a Part with supports also came out with some problems using FTD snow white resin (Base 50000ms and 18000ms)

    IMG_0304.jpg

    these supports generated in meshmixer and printed with CW.
    the part contact with supports having rough finish and some short fill, But the build over that area is looking good finish.
    I think its the problem with supports stability.

    also suggest how to finish the parts.

  8. #65
    Regular 3D Printer
    Join Date
    Jan 2016
    Posts
    93
    Post Thanks / Like
    Nice one Karthik and good to see you are on your way to making some good prints. Some good tips there from mojor also. I would suggest the following:

    - The largest area should be in contact with the build plate, therefore the side where it has flaked due to no support should be on the plate.
    - The problem you have with the part breaking at the top is due to too much adhesion. Although this is good, you should have built a thin supporting layer around it (even 1 layer thick) that you can cut off in post-production. This layer should extend around 10mm around the whole part and is easy to break off then sand.
    - I would add some supports inside the compartments that you can cut off later.
    - Regarding your print that had the support failure, make sure the contact points are 0.5 or 0.6mm as anything thinner will cause a failure.

    My finishing techniques mainly consist of sanding but I will put up a separate post on this to show before and after results and show the sandpaper and files I use.

    I have attached a picture showing the thin layer that I print and remove later. This gives better bed adhesion and means you don't need to print and cure a separate layer and also gives you a layer to get the knife under to remove the piece without damaging it.

    Screenshot 2016-12-27 11.52.44.jpgScreenshot 2016-12-27 11.52.18.jpg

    Finished and sanded:

    IMG_5643.jpgIMG_5645.jpg
    Last edited by sukhvir; 12-27-2016 at 01:26 PM.

  9. Thanks karthik.pdy thanked for this post
    Likes karthik.pdy liked this post
  10. #66
    3D Printer Noob
    Join Date
    Aug 2016
    Location
    India
    Posts
    29
    Post Thanks / Like
    Thanks @ Sukhvir for your strategic solution. eagerly waiting for your Finishing Forum

    kindly let me know the process in cleaning the VAT and Build plate

    How much accuracy you will get ?
    Last edited by karthik.pdy; 12-28-2016 at 06:20 PM.

  11. #67
    Regular 3D Printer
    Join Date
    Jan 2016
    Posts
    93
    Post Thanks / Like
    Hi Karthik. Not sure what you mean by accuracy, but print sizes are as I expect them to be, as long asI increase the model size by 0.4% to compensate for shrinkage. with regards to cleaning the build plate and vat, not sure what information you are looking for. If it's for a resin colour change, I empty out resin, unscrew bolts, remove film and clean everything with isopropyl alcohol before piecing back together. The build plate should be cleaned before every print to remove any debris, however you can lightly sand the surface now and again to keep it clean.

  12. Thanks karthik.pdy thanked for this post
    Likes karthik.pdy liked this post
  13. #68
    3D Printer Noob
    Join Date
    Aug 2016
    Location
    India
    Posts
    29
    Post Thanks / Like
    Hi Sukhvir & all

    I tried a part with 1.5mm supports ribs and gap between ribs 6mm, I added 5 degrees rotations with respective to X & Y

    but there is some issues in formation in below images. kindly suggest

    Inner side is perfect

    IMG_0421.jpgIMG_0422.jpgIMG_0423.jpgIMG_0424.jpg

  14. #69
    Regular 3D Printer
    Join Date
    Jan 2016
    Posts
    93
    Post Thanks / Like
    Hi Karthik,

    Can you please send me the stl file so I can see how it should look? I can recommend supports after looking at it.

  15. #70
    3D Printer Noob
    Join Date
    Aug 2016
    Location
    India
    Posts
    29
    Post Thanks / Like
    Quote Originally Posted by sukhvir View Post
    Hi Karthik,

    Can you please send me the stl file so I can see how it should look? I can recommend supports after looking at it.
    Hi Sukhvir

    kindly download STL https://www.dropbox.com/s/8zkdzm89rz...cover.rar?dl=0

 

 

Similar Threads

  1. Paypal blocks successful Indiegogo 3D printing campaign
    By bolsoncerrado in forum Latest News
    Replies: 2
    Last Post: 05-09-2016, 02:36 PM
  2. My First Successful Print!
    By jase3d in forum Rapide Lite 3D Printers
    Replies: 62
    Last Post: 02-11-2015, 01:29 PM
  3. REVIEW: Rapide Lite 200 + AstroPrint = Successful print!
    By bolsoncerrado in forum Rapide Lite 3D Printers
    Replies: 7
    Last Post: 01-22-2015, 02:04 PM
  4. First few prints
    By ievolve in forum Rapide Lite 3D Printers
    Replies: 5
    Last Post: 12-29-2014, 03:36 AM
  5. My First Successful Print!
    By synthius in forum Rapide Lite 3D Printers
    Replies: 4
    Last Post: 12-13-2014, 09:07 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •