Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 1 of 1
  1. #1
    Regular 3D Printer
    Join Date
    Jan 2016
    Location
    Moscow Russia, Naples USA
    Posts
    69
    Post Thanks / Like

    Exclamation How to make a nice aluminum etching at home or in a small workshop.

    How to make a nice aluminum etching at home or in a small workshop. Full guidance from Endurance.
    We are often asked the same question, and whether it is possible to make an engraving with a laser L-Cheapo on metal, such as aluminum. Is it even possible to make engraving on metal in the home?
    Today, we will answer this question.
    In fact it is fairly common in domestic metal, suitable for engraving. Many products, such as key chains, sticks, some mobile body and flash cards are made of aluminum.

    So, what do we know about aluminum? This metal has melting temperature of about 600 degrees Celsius, has high thermal conductivity and having, typically on its surface a layer of aluminum oxide has a melting temperature greater than 1000 degrees Celsius. This significantly complicates the process of engraving by heat treatment, but there is another option. Aluminum - a good conductor, and if so, then the process of electrolysis has not been canceled. Here it is the same decision, which we describe.
    This process is called aluminum etching.
    This is no big deal. We only need a current source of 9-12 volts.
    As well as ordinary salt (NaCl), the capacity of the dielectric (plastic is fine), nail or any iron object suitable shape and size, water.
    And, of course, the laser!
    So what and how do we do?
    1. Prepare bitmap, which would be applied to the aluminum surface of the plate.
    For example, here is this:
    1.png
    2. Cover the aluminum plate surface with a protective film (adhesive tape, paint, paint on the selection).

    2.png

    3.png

    3. Place the aluminum plate on the top of 3D-printers equipped with our (specify how) laser, and include laser cutting mode (to remove the tape and pasted to create open areas in the future site of the engraving).

    4.png

    4. Next, in the plastic container we prepare a concentrated aqueous solution of NaCl.

    5.png

    5. From the source of electric current terminal 2 wire "plus" and "minus".
    6. To connect the positive terminal with our aluminum plate and also to omit the salt solution.
    7. Power on

    6.png

    8. Starting the electrolysis process (etching) in solution. Depending on the strength of the current and the concentration of the solution can estimate the approximate time necessary for etching. Usually 3-5 minutes.

    7.png

    9. We take the product out from the solution.

    8.png

    9.png

    It must be remembered that the engraved product before being placed in the solution should be carefully isolate the exception of those areas where, in fact, engraving is to be applied.
    This process can be carried out both at home and in a small workshop.
    With this technology, anyone can become a master of engraving on metal (aluminum).
    In our opinion, this technology has great practical value.
    Subscribe to updates Endurance.
    Engraved with Endurance - it's easy!
    Watch full demo:
    https://www.youtube.com/watch?v=ajU8XB5SnYE

    Learn more on our web sites and our youtube channels:
    https://www.youtube.com/watch?v=btoPcWX9iWo
    https://www.youtube.com/watch?v=ajU8XB5SnYE
    https://www.youtube.com/watch?v=j1_itpuYNkE

    EnduranceRobots.com and EnduranceLasers.com
    Text us or call +7 916 225 4302 (viber / whatsapp) or skype: George.fomitchev
    Last edited by ENDURANCE; 07-19-2016 at 09:21 AM.
    ENDURANCE ROBOTS

    We love everything that can be 3D printed!
    -------------------------
    EnduranceRobots.com
    EnduranceLasers.com

 

 

Similar Threads

  1. Replies: 0
    Last Post: 07-23-2016, 08:59 AM
  2. Do it yourself from A to Z. Present you a diode laser etching of a PCB.
    By ENDURANCE in forum 3D Printers - Other Brands
    Replies: 0
    Last Post: 06-26-2016, 10:09 PM
  3. ”How to make your own circuit board at home!”
    By ENDURANCE in forum Off-topic
    Replies: 0
    Last Post: 04-27-2016, 08:38 PM
  4. Creation Workshop Manual
    By bolsoncerrado in forum Morpheus 3D Printers
    Replies: 0
    Last Post: 02-29-2016, 11:20 AM
  5. Small Feed Hole Defect on Extruder
    By Fixx in forum Rapide Lite 3D Printers
    Replies: 7
    Last Post: 01-13-2015, 09:56 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •