Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 7 of 7
  1. #1
    Regular 3D Printer
    Join Date
    Dec 2014
    Location
    Italy
    Posts
    74
    Post Thanks / Like

    Z axis stepper motor dead after upgrading

    Hello, like topic said, I've tried upgrading my Rapide Lite firmware to latest git version.

    I've configured, Configuration.h pins_RUMBA.h according to the old firmware, everything fine, except now, only the left Z stepper motor it's moving.

    But its not dead, if I downgrade to the old fimware start to work fine again so i think it's something erroneous into configuration of the new firmware. Any idea?

    Regards

  2. #2
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,059
    Post Thanks / Like
    Sounds like a setting is off in that firmware...

  3. #3
    Regular 3D Printer
    Join Date
    Dec 2014
    Location
    Italy
    Posts
    74
    Post Thanks / Like
    Quote Originally Posted by bolsoncerrado View Post
    Sounds like a setting is off in that firmware...
    yes sounds to me too

  4. #4
    Regular 3D Printer
    Join Date
    Dec 2014
    Location
    Italy
    Posts
    74
    Post Thanks / Like
    I hhink i've found the problem:

    Configuration_adv.h

    Code:
    // A single Z stepper driver is usually used to drive 2 stepper motors.
    // Uncomment this option to use a separate stepper driver for each Z axis motor.
    // The next unused E driver will be assigned to the second Z stepper.
    //#define Z_DUAL_STEPPER_DRIVERS
    I've uncommected out that but now it doesnt compile the firmware ehehehe:

    Code:
    C:\Users\Davide\AppData\Local\Temp\ccGDtEh3.ltrans0.ltrans.o: In function `process_next_command()':
    
    
    ccGDtEh3.ltrans0.o:(.text+0xc66): relocation truncated to fit: R_AVR_7_PCREL against `no symbol'
    
    
    collect2.exe: error: ld returned 1 exit status
    
    
    exit status 1
    Errore durante la compilazione per la scheda Arduino/Genuino Mega or Mega 2560.

  5. #5
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,059
    Post Thanks / Like
    try with an older IDE software version...

  6. #6
    Regular 3D Printer
    Join Date
    Dec 2014
    Location
    Italy
    Posts
    74
    Post Thanks / Like
    tried doesnt compile

  7. #7
    Regular 3D Printer
    Join Date
    Dec 2014
    Location
    Italy
    Posts
    74
    Post Thanks / Like
    Finally got the new firmware with arduino ide 1.6.10 and last RCbugFix. The development branch doesnt compile

 

 

Similar Threads

  1. Upgrading a Rapide Lite 200 with a Smoothieboard 5x
    By bolsoncerrado in forum Rapide Lite 3D Printers
    Replies: 1
    Last Post: 08-21-2016, 12:22 PM
  2. Dead Printers Club
    By xyz in forum Rapide Lite 3D Printers
    Replies: 22
    Last Post: 06-26-2015, 02:22 PM
  3. Optimal stepper driver current settings?
    By cshaw85 in forum Rapide Lite 3D Printers
    Replies: 2
    Last Post: 01-18-2015, 09:07 AM
  4. Stepper Motor Specs
    By CrazyCoder in forum Rapide Lite 3D Printers
    Replies: 2
    Last Post: 01-07-2015, 08:17 AM
  5. Missing tension screws on Y axis motor
    By Broome in forum Rapide Lite 3D Printers
    Replies: 5
    Last Post: 12-27-2014, 02:34 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •