Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 2 of 2
  1. #1
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,059
    Post Thanks / Like

    Upgrading a Rapide Lite 200 with a Smoothieboard 5x

    Upgrading a Rapide Lite 200 with a Smoothieboard 5x

    Posted by Antony T Curtis at 3/28/2016 01:49:00 am

    The Rapide Lite 200 originally came with a RUMBA based controller board which is based upon an Atmel ATMEGA based microcontroller. However, I had encountered issues where the board's USB interface would reset during a print and thus ruining a print. The controller board uses a smaller Atmel microcontroller to provide the serial to USB interface and it's possible that there is some instability there.



    Original Rapide controller



    I had a Smoothieboard from a Kickstarter which I had intended to use for a CNC router project but I decided to repurpose it for upgrading the Rapide printer. The Smoothieware web site does have extensive information on making use of the Smoothieboard.


    Smoothieboard 5x


    The printer has 5 stepper motors, of which two are used to drive the y-axis. I could have chosen to drive both from the same driver chip but I decided to drive each of the stepper motors from their own driver. To make the two stepper motors step together, a few links had to be soldered onto the Smoothieboard. In order to keep things as simple as possible, I decided to keep the order in which the stepper motors plug onto the controller board the same. I also soldered the same connectors to the Smoothieboard to avoid needing to recrimp new connectors onto the cables.


    Three jumpers centered

    The were changes in the order of the power connectors. the power for the main board which was connected to the terminal labelled MAIN-PWR was then connected to the main board power input on the right of this image shown as 12-24v:



    Be mindful to make sure that the polarity is correct.

    The HB-PWR cables was then connected to the PWR IN connector at the bottom centre of the board and JP28 was jumpered for the fan power. The heater bed HB-OUT was then connected to P2_7 connector and the head heater HE0 connected to P2_5.

    The thermistor and endstops were plugged in as one would expect.


    Thermistor and endstop connections on original controller board


    Initial install of smoothieboard

    When I had initially set up the smoothieboard, I did not have the recommended 5V regulator installed so I had used a separate regulator board for the 5V power. I later installed the recommended 5V regulator (marked as VBB). I also ended up securing the board using adhesive PCB standoffs.





    Cables tidied a bit and heatsinks added

    The firmware install and upgrade is simply a case of putting the firmware.bin file in the root directory of a DOS formatted SDCARD. Instructions are available at: http://smoothieware.org/flashing-smoothie-firmware





    A copy of my current config.txt is available here: config.txt



    I do have my Smoothieboard plugged into my network so I have the ethernet enabled in my config.

  2. #2
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    3,059
    Post Thanks / Like
    Note from admin: Please note that smoothieboard works at 1/16 microsteps while the RUMBA/Rapide board can work up to 1/32 microsteps.

 

 

Similar Threads

  1. My Rapide Lite 312
    By clayton in forum Rapide Lite 3D Printers
    Replies: 16
    Last Post: 11-07-2016, 11:50 AM
  2. Z axis stepper motor dead after upgrading
    By Gort in forum Rapide Lite 3D Printers
    Replies: 6
    Last Post: 08-18-2016, 08:36 PM
  3. So, who's willing to try them on their Rapide Lite's? :D
    By bolsoncerrado in forum Rapide Lite 3D Printers
    Replies: 4
    Last Post: 07-09-2015, 01:58 AM
  4. Rapide Lite 500
    By bolsoncerrado in forum Rapide Lite 3D Printers
    Replies: 2
    Last Post: 04-16-2015, 08:12 PM
  5. Rapide Lite 350
    By Bah in forum Rapide Lite 3D Printers
    Replies: 19
    Last Post: 03-05-2015, 04:10 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •