Thanks Thanks:  13
Likes Likes:  6
Dislikes Dislikes:  0
Page 21 of 26 FirstFirst ... 111920212223 ... LastLast
Results 201 to 210 of 252
  1. #201
    3D Printer God(dess)
    Join Date
    Nov 2016
    Posts
    1,051
    Post Thanks / Like
    Just this one. I wanted to initialize it using a test print... stopped it half way. Still 100%; purged... 100%; test print 1/2 way again - 100%; and the chip holders... 100%!
    So I moved it to an upgraded unit and sure enough, recognized and printing!

    This chip should be cloned!

  2. #202
    Regular 3D Printer
    Join Date
    Jul 2017
    Posts
    32
    Post Thanks / Like
    It's a great tool. It will save my cube 3's life if it can work like official.

    I have printed some things using hacked firmware. But it throws T22, T23 and T24 error frequently.

    At first I suspected to be a third party filament. But the thing confused me is using the same filament, remove and then re-installed back, the error T22, T23 or T24 throws.

    Today I have tried to print using the original firmware and hacker firmware twice alternately.

    Using hacked firmware and right extruder, it throws T22, T23 and T24 errors frequently. After returning to the original firmware, It works fine.

    Purging simetimes works fine, sometimes not work with hacked firmware.

    I know Cube Toolbox dose not change anything but prevent to write the filament usage to the chip. But I can not figure out what is going on.

    Could you save me? 😊

  3. #203
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    2,935
    Post Thanks / Like
    Which is your current ambient temp where the printer is?

  4. #204
    Regular 3D Printer
    Join Date
    Jul 2017
    Posts
    32
    Post Thanks / Like
    About 26℃ in an air-conditioned room.

    In order to avoid the problem of air conditioning, I have tried to use a large plastic box to cover up the printer, but it has limited effect.

  5. #205
    3D Printer God(dess)
    Join Date
    Nov 2016
    Posts
    1,051
    Post Thanks / Like
    At 20*C and above, you should have no problems.

  6. #206
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    2,935
    Post Thanks / Like
    Yeah sounds weird to be at 26 and "air conditioned"

  7. #207
    Regular 3D Printer
    Join Date
    Jul 2017
    Posts
    32
    Post Thanks / Like
    Yeah. I'm in china and using google translation. 😄

    I'm using hacked firmware that attached in the thread. It's work now. I'm testing and see whether the problem still exists.

    - - - - - - - - - -

    It shows T22 error again after restart the printer.

    It worked well in the two days printing without restarting. But it shows T22 error always after restarting just now.

  8. #208
    3D Printer God(dess)
    Join Date
    Nov 2016
    Posts
    1,051
    Post Thanks / Like
    I believe I remember reading an overactive thermistor can do this. Somewhere on the openbuilds forum. They just added foil and it behaved.

    However, you are getting this only on a FW change. That is not something anyone has reported before.

    I knew the list was here somewhere...

    http://www.print3dforum.com/showthre...perature+error

    - - - - - - - - - -

    Bo, you might want to link this to the 1st page.


  9. #209
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    2,935
    Post Thanks / Like
    Nice vid! Thanks.

  10. #210
    3D Printer Noob
    Join Date
    Aug 2017
    Posts
    9
    Post Thanks / Like
    hi all

    I have orginal 3d system Pla plastic exstruid is ok . purge printing

    buy other pla plastic not exstuide . purge not printing (parameter http://rcl.lt/index.php?id=2&lang=lt...75PLA/B&pmode=)

    I tried program cube 3d modifier 2.0 change parameters to 210c But nothing changes, but plastic does not fit in anyway

    pllzzz help i beginer first fillaments

 

 

Similar Threads

  1. Replies: 23
    Last Post: 04-21-2017, 04:36 PM
  2. Replies: 0
    Last Post: 02-26-2017, 10:55 AM
  3. [ HOW TO ] Modify the Cube3 Cartridges to accept 3rd party filament (WIP)
    By bolsoncerrado in forum Cube3
    Replies: 2
    Last Post: 01-31-2017, 09:17 AM
  4. IKEA hack lets you create a 3D printer enclosure for cheap
    By bolsoncerrado in forum Latest News
    Replies: 1
    Last Post: 08-15-2016, 12:30 PM
  5. The 3D Nefertiti Hack
    By bolsoncerrado in forum Latest News
    Replies: 6
    Last Post: 03-01-2016, 05:24 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •