Thanks Thanks:  8
Likes Likes:  17
Dislikes Dislikes:  0
Page 2 of 13 FirstFirst 123412 ... LastLast
Results 11 to 20 of 128
  1. #11
    Regular 3D Printer
    Join Date
    Jan 2017
    Posts
    71
    Post Thanks / Like
    The biggest impression made on my Cube3, I had to turn it because there was space in the bed!

    WhatsApp Image 2017-02-07 at 00.01.43.jpgWhatsApp Image 2017-02-07 at 00.01.43(1).jpgWhatsApp Image 2017-02-07 at 00.04.27.jpg

  2. Thanks bolsoncerrado thanked for this post
    Likes bolsoncerrado liked this post
  3. #12
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    2,905
    Post Thanks / Like
    J******DER tio! El p*to amo!! xD Bravo!!!

    A que le das? Coches? Helis?

  4. #13
    Regular 3D Printer
    Join Date
    Jan 2017
    Posts
    71
    Post Thanks / Like
    Thank you! I fly airplanes and racing drones .. My nick of war: Ironman

    - - - Updated - - -

    These are my custom engine protectors:
    WhatsApp Image 2017-02-14 at 12.55.19.jpg
    WhatsApp Image 2017-02-14 at 12.55.19(1).jpg
    Last edited by Programeitor3d; 02-14-2017 at 05:55 PM.

  5. #14
    3D Printer God(dess)
    Join Date
    Nov 2016
    Posts
    1,028
    Post Thanks / Like
    Excellent!!! If only I had the ability to actually fly a drone instead of clipping all the hedges.

  6. #15
    3D Printer God(dess)
    Join Date
    Nov 2016
    Posts
    1,028
    Post Thanks / Like
    Here is a single wall geometric widget...
    Attached Files Attached Files
    Last edited by TommyDee; 02-17-2017 at 03:38 AM.

  7. #16
    3D Printer God(dess)
    Join Date
    Nov 2016
    Posts
    1,028
    Post Thanks / Like

  8. #17
    Expert 3D Printer
    Join Date
    Jan 2017
    Posts
    241
    Post Thanks / Like
    Worked a little on my dual extruder profile for simplify3d and did some comparisons to cube print. Looks like I have it about right to get some good prints. Only issue is that I have to use a prime tower with simplify3d but I have a good idea of what I need to change to no longer need it.

    edit- Forgot to mention that my cube glue wasn't dry when I did the simpidy3d cube and the sides were curling up since they weren't being held down


    20170222_174615.jpg

    20170222_174625.jpg

    20170222_174759.jpg

    20170222_174830.jpg
    Last edited by Mythandar; 02-23-2017 at 06:36 AM.

  9. Likes bolsoncerrado liked this post
  10. #18
    3D Printer God(dess)
    Join Date
    Nov 2016
    Posts
    1,028
    Post Thanks / Like
    You have a lot of patience, M. What's with the sag on the Simply3D cube?

    I now have a couple of "Fossil" key-chains in 2 color prints. They work great with cube's slicer.
    Good filament tester!

  11. #19
    Expert 3D Printer
    Join Date
    Jan 2017
    Posts
    241
    Post Thanks / Like
    I had forgotten to put that the cube glue wasn't dry on the simplify3d cube so it wasn't stuck enough to prevent warping. they were both printed in abs.

  12. #20
    Administrator bolsoncerrado's Avatar
    Join Date
    Nov 2014
    Posts
    2,905
    Post Thanks / Like
    Also Im assuming you're all on 1.0 patched firmware? Can you use PLA or ABS no matter what in either of the sides of the Cube?

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •